Kanal VarnaDrains • Leaks • Thermal imaging • Plumbing
Hands fitting a mixer tap on a bathroom basin

Tap installation in Varna: kitchen, basin, bath and shower mixers

A dripping kitchen tap, a wobbly basin mixer or a new tap you bought for the bathroom? The plumbers we work with remove the old one, fit the new one on new hoses and test every joint for leaks. We tell you the price before we start.

Our clients on video · all videos (in Bulgarian)

30–60 minA standard tap fitting
Old tap removedIncluded in the job
06:00–23:00Every day, weekends included
Pay after the jobCash, card or bank transfer
1000+ clients served 30+ years in the trade Price agreed before we start 06:00–23:00 every day
In short

Need tap installation in Varna? Kanal Varna arranges the fitting of kitchen, basin, bath, shower and thermostatic mixers in flats and houses in Varna and along the coast. The plumbers we work with remove the old tap, check the hoses and the small isolating valves under the sink, fit the new tap and test for leaks; a standard fitting takes 30 to 60 minutes. We tell you the price before we start, once you have described the job or sent photos. We work every day from 06:00 to 23:00. Call +359 52 993 333 or email info@kanalvarna.com — write to us in English and we reply in English. All the other planned jobs are on our plumber in Varna page.

Updated November 2026

Tap installation in Varna: what we fit

A mixer tap looks like a ten-minute job until it is badly done: then it drips under the sink, the pressure is poor, tiles get damaged, and in the worst case the kitchen floods. The plumbers we work with fit all the usual kinds in flats and houses.

  • Single-lever mixers — the most common kind: one lever for temperature and flow, with a ceramic cartridge that can be replaced later.
  • Two-handle taps — separate hot and cold. Classic look, now less common.
  • Thermostatic mixers — hold the temperature you set, which is useful in a shower with children.
  • Sensor taps (no-touch) — switched on by movement; they need a battery or a mains supply.
  • Kitchen taps with a pull-out spray — a flexible hose for rinsing the sink; the fitting is a little different.
Hands fitting a mixer tap on a bathroom basin

Bath and shower mixers go on the wall. A built-in (concealed) mixer is a bigger job, because its body sits inside the wall and the tiling has to be opened — that is normally done as part of a bathroom renovation rather than as a stand-alone fitting.

How a tap is replaced

  1. Water off, old tap out. We close the water, remove the old tap and clean the area where it sat.
  2. Check what is underneath. The flexible hoses, the small isolating valves under the sink and the mounting holes are looked at before anything new goes on.
  3. New tap on new hoses. The new tap is fitted with new hoses and seals.
  4. Water on, test. We run the water and look at every joint for leaks and check the tap works properly.

Removing the old tap is part of the job. A standard fitting takes 30 to 60 minutes. Pay after the job, in cash, by card or by bank transfer; an invoice on request.

Before you buy or call: three things worth checking

  • Buy the tap and the hoses yourself. Ask us for a suggestion if you want one. If you are not sure the tap will fit your sink or wall, send us a photo of the box or the model name.
  • Wall mixers: the distance between the two supply points. Standard is 150 mm, but 100 mm also exists. Old installations may also have corroded wall connectors (eccentrics) with an unusual thread, and then they are replaced together with the mixer, otherwise the new tap leaks too.
  • Pipe size. A tap needs to match the pipe connection (half or three-quarter inch). If you want more flow and the old steel pipes are narrowed by corrosion, a new tap will not help — the pipe section needs replacing, see pipe replacement.

Fitting a basin tap yourself is possible if you are handy. A bath or shower mixer, or an old installation, is riskier: it is easy to damage a pipe or a fitting.

Tell us which tap and where, send a photo of the old one — we tell you the price before we start and when we can come.

📞 +359 52 993 333

Replace the hoses and the isolating valves at the same time

When an old tap is replaced, it is sensible to replace the small valves under the sink as well. They are brass or chrome and over the years they corrode or seize, so they no longer close when you need them to. A seized valve is exactly what you find when a hose bursts at night. New stainless-steel valves let you shut off one tap without turning off the water for the whole flat.

The flexible hoses live for about five to eight years, and old rubber ones are the most common cause of the "unexpected" flood in a kitchen or bathroom. With a new tap, fit hoses with a braided stainless-steel sleeve: plastic ones crack. If you are replacing the sink as well, the tap and the sink trap are fitted in one visit, so the joints are made once and tested together.

Dripping tap: repair or replace?

Not every dripping tap needs replacing. It depends on which part is worn and whether a spare exists.

What you seeWhat it usually isWhat happens
Drips from the spout (single lever)Worn cartridgeCartridge replaced if the same one can be found; the usual sizes are 35 and 40 mm but odd ones exist, so do not buy one in advance
Drips from the spout (two handles)Seals or ceramic headsUsually repaired
Water under the sinkHoses or isolating valves — often the tap is fineWe look at the hoses and valves first
Bath: water from spout and shower at onceWorn diverterOften only the diverter is replaced
Only cold or only hot from a thermostatic mixerBlocked inlet filters or a worn thermostatic cartridgeFilters cleaned first; cartridge replaced if a spare exists
The tap wobblesLoose nut under the sink or worktopTightened, nothing replaced
Weak flowBlocked aerator (the mesh at the tip)Cleaned in a few minutes

We suggest replacing the tap when the body is cracked or corroded, when spares cannot be found, or when the repair would cost almost as much as a new tap. If only the hot water is weak and the aerator is clean, the cause may be the water heater — see water heater repair. If several taps start dripping one after another and the pipes knock when you close them, the water pressure may be too high: pressure reducing valve.

If you are not in Bulgaria

You do not need to be there. Send us the address and the name and phone number of whoever can open the door — the property manager, the cleaner, a neighbour or the guest — and we arrange the visit with them. Tell us whether the tap is already bought and where it will be delivered.

Photos help us a great deal. Take the tap from the front and from underneath, the brand and model if you can read them, and the place where it drips. That way the plumber can bring the right part on the first visit. Send them by email to info@kanalvarna.com.

Frequently asked questions

How much does tap installation cost?

It depends on the type of tap — kitchen, basin, bath, shower or thermostatic — and on whether the valves and hoses need replacing too. We tell you the price before we start, once you have described the job or sent photos. Starting prices for some other jobs are on the plumber in Varna page.

How long does it take?

A standard fitting takes 30 to 60 minutes. A built-in mixer in the wall is a larger job and is usually done during a bathroom renovation.

Is removing the old tap included?

Yes, taking out the old tap is part of the job.

Do I buy the tap first?

Yes, buy the tap and the hoses. If you want a recommendation for the kitchen, we suggest a single-lever mixer with a high spout and a pull-out spray, which is easy for large pans and jugs.

I'm not in Bulgaria. Can you still deal with it?

Yes. Send us the address and the contact of whoever can let us in, plus photos of the tap. We arrange the visit with them, agree the price with you before we start, and you can pay by bank transfer.

What if it leaks after fitting?

Get in touch and we tell you what to do. Keep the receipt and the paperwork that came with the tap, and note the model — it makes spare parts easier to find.

Can I contact you in English?

Yes — write to us in English by email at info@kanalvarna.com or through the form on this page, and we reply in English. The phone number is +359 52 993 333.

New tap to fit?

Tell us which tap and where, send a photo of the old one — we tell you the price before we start and when we can come.

📞 +359 52 993 333

or email info@kanalvarna.com — write in English and we reply in English.

Send us a message

Leave your name and a phone number with the country code. Add your email if you prefer a written reply — write in English and we reply in English. We confirm the price before any work starts.

📞