Window and door repair in Varna: uPVC, aluminium and timber
Sashes adjusted, new seals, and finding where the draught really comes in — for uPVC, aluminium and timber windows and balcony doors in Varna. New windows we do not sell or fit.
Our clients on video · all videos (in Bulgarian)
Window repair in Varna is usually two things: adjusting the sashes and replacing the old seals. After that a uPVC, aluminium or timber window closes easily again and stops letting in the cold. A new window is only needed when the frame is bent or cracked, and we do not sell or fit new windows, so we have no reason to push you towards one. First we look at where the problem is, and in cold weather we also use a thermal camera. The work is done by the craftsmen we work with: we organise it and stay your one phone number. Call +359 52 993 333 or email info@kanalvarna.com — write to us in English and we reply in English.
Updated November 2026What we repair on windows and doors, and what we do not
The aim of a window repair is simple: the window or balcony door you already have should close easily again, press tight against the frame and keep out cold and water. We do not replace whole windows; if a frame needs replacing, we tell you plainly.
Window frame, sash and hardware. The frame is fixed in the wall; the sash is the part that opens; the hardware is the hinges, handle and locking mechanism. Depending on the profile, the window is uPVC, aluminium or timber.
Window adjustment
The sash rubs, has dropped, does not lock or the handle is stiff. The hinges and the locking cams are adjusted.
Window seal replacement
It is cold next to the closed sash and the seals are hard or cracked. First where the air comes in, then new seals.
Double glazing unit replacement
Misted between the panes, cracked or with a cracked edge: measured, ordered to size and replaced in the sash.
Internal door fitting
Interior doors, a bathroom door and the front door of a flat — from measuring the opening to the architraves.
Window reveals
Finishing around new windows: protected foam, skim or board, corner beads and the window board.
A broken handle or hinge is also a repair, but the part has to be ordered for that specific system. Whether we can take that on, we tell you by phone after seeing a photo.
The sign, the likely cause and what is done
| What you notice | Likely cause | What is done |
|---|---|---|
| The sash is hard to close, rubs at the bottom or the handle is stiff | The sash has dropped, the cams miss their keepers, the hardware is dry | Cleaning, lubricating and adjusting the sash |
| A draught around the closed sash, cold next to the window | Hardened or squashed seals, weak pressure | Finding where the air comes in, then a seal replacement |
| The glass is wet on the inside in the morning, black spots on the frame | Humid air in the home or a cold spot around the window | Not a fault of the window — see mould and damp |
| Water on the sill or under the balcony door after rain | Blocked drain slots, or water coming in from outside | Clearing the slots; if the water comes from outside, see balcony leak |
| Misted between the two panes | The glass unit has lost its seal | A new double glazing unit, ordered to size |
| A draught between the frame and the wall | Crumbling fitting foam, cracked reveal | New foam and reveal on the inside — whether we take it on, we say by phone; the outside joint above the second storey we do not take on |
The signs often mix: a balcony door that has dropped both rubs and lets in cold at the top corner. That is why we start with the adjustment — a new seal will not press if the sash is not sitting where it should.
uPVC, aluminium and timber: what differs in a repair
The principle is the same for all three: the sash must sit exactly in the frame and press evenly on the seal. The weak points differ.
- uPVC. The most common window in panel blocks and newer buildings. The hardware adjusts in three directions and the seals can be replaced. The balcony door usually goes first.
- Aluminium. Old aluminium frames without a thermal break, common on glazed-in balconies, get cold all over and collect water. New seals stop the draught, but the frame stays cold. Aluminium with a thermal break is repaired much like uPVC.
- Timber. Old timber windows often have no seals at all, and the wood swells with damp so the sashes stick. Rotten wood is a job for a joiner.

Near the sea the steel parts of the hardware rust faster. There is no stock of spare parts: seals and parts are chosen from a sample or a photo for the specific profile.
Tell us the profile and how many sashes — by phone we say whether and when we can come and what it will cost.
📞 +359 52 993 333Repair or a new window: when repair makes sense
A window repair is worth it when the frame is sound and straight and the problem is in the adjustment, the seals or a single part:
- the frame and sash are straight — with the sash closed, the gap is the same all the way round;
- there are no cracks in the profile, especially at the corners where a uPVC frame is welded;
- the glass unit is intact and not misted between the panes — or you will replace it separately;
- the timber is sound, with no rot.
A new window makes more sense when the sash is bent, the profile is cracked or the timber is rotten. Before you replace a window, show us where the draught is. The cold next to a window often comes not from the sash but from the joint between frame and wall, from the sill or from the roller-shutter box, and a new window fitted the same way will not cure it. In cold weather we check it with a thermal camera — the same one we use for thermal imaging surveys of homes.
How a window repair visit goes
- Call and photos. We ask what the profile is, how many sashes there are and what bothers you, and on that call we say when we can come.
- Looking at every sash. Not only the one you called about: the gaps, the rubbing marks, the seals and the drain slots. The pressure is checked with a sheet of paper.
- Thermal camera if the weather allows. With about 10–15 °C or more between inside and outside, the camera shows the cold streaks along the sash and the frame. On warmer days the draught is found by hand and with paper.
- Repair on site. Cleaning and lubricating the hardware, adjusting the sashes, and new seals if that was agreed.
- Final check. Every sash must close without effort and press evenly. You are shown how to switch the cams between summer and winter setting.
What to tell us by phone, and what the price depends on
We give the price by phone after a short description. To make it accurate, tell us:
- the profile — uPVC, aluminium or timber — and roughly how old it is;
- how many sashes and doors need attention, and which of them open and tilt;
- what exactly is wrong — rubbing, not locking, draughty, water on the sill;
- a close-up photo of the bottom hinge and of the seal, if you can — the system can be recognised from them.
The price depends on the number of sashes, the metres of seal, whether hardware parts are needed and how long the work takes. We work every day from 06:00 to 23:00 and issue an invoice. If you are abroad, tell us who will open the flat.
When you do not need anyone for your windows
- Autumn has come and you feel cold along the sash? Switch the adjustable cams to the stronger, winter setting — the steps are on the window adjustment page.
- Water on the inside sill after rain? Clear the slots in the bottom of the frame with a soft wire or a stick and pour in a little water: it should run out. Do not seal them with silicone.
- The glass mists only along the bottom edge on cold mornings? That is not a fault. Airing the room more often and for shorter spells usually helps.
If the sash still rubs or lets in cold after that, call us. Small jobs around the window that are not the window itself — a curtain rail, a shelf, a TV bracket — are for the handyman.
All services: windows and doors
A sash that rubs, sags, will not lock or has a stiff handle: hinges and cams set again Window seal replacement
A draught along the closed sash, hard or cracked seals: first where the air comes in Glass unit replacement
Misted between the panes, cracked glass or a chipped edge: measured, ordered to size, replaced Window reveals
Grey foam and a bare joint after the window company: reveals, window board, drip edge Internal door fitting
Interior, bathroom and entrance doors you have bought: opening measured, frame set level, door hung
Frequently asked questions
Do you repair aluminium windows?
Yes, when the system has a tilt-and-turn sash and hardware similar to uPVC: then the sash is adjusted and the seals replaced. On sliding aluminium systems on glazed-in balconies it is usually the rollers and brushes that wear. Old aluminium without a thermal break stays cold even after a repair, and we tell you that beforehand.
Is it worth repairing 15-year-old windows?
Usually, yes. At that age a uPVC profile is usually sound; the problems are seals that have hardened and sashes that have dropped. If the frame is straight and the corners are not cracked, adjustment and new seals put the window back in good order without the cost and the mess of a new one.
Will you come for a single window?
Ask us — when we can come for one sash, we tell you by phone. If other sashes are hard to close too, mention them all at once: looking at every window takes a little longer, and it often shows the problem is not only in the one.
Do you make timber windows?
We repair them, we do not make them. On old timber windows loose hinges are tightened, the sashes sealed, and you are told which parts are rotten. Making new sashes, replacing rotten pieces and painting are for a joiner; a photo usually shows which of the two you need.
Do you replace whole windows?
No, new windows are not our work. If at the visit we see the profile is bent, cracked or rotten, we tell you honestly that a repair will not last, and what to ask of the window company — for example, to check the joint around the frame and not only the window.
I let my flat out and live abroad. Can you sort out the windows?
Yes. Email us photos of the windows, the bottom hinge and the seal, with the address, and tell us who can open the door. Write to us in English and we reply in English; you get the price before the work.
The window rubs, will not lock or lets in a draught?
Tell us the profile and how many sashes — by phone we say whether and when we can come and what it will cost.
📞 +359 52 993 333or email info@kanalvarna.com — write in English and we reply in English.
Send us a message
Leave your name and a phone number with the country code. Add your email if you prefer a written reply — write in English and we reply in English. We confirm the price before any work starts.