Kanal VarnaDrains • Leaks • Thermal imaging • Plumbing
A window pane with cracks branching out from a single point, in a white frame

Double glazing unit replacement in Varna: misted or cracked glass

Fog or droplets between the panes, or a crack running across the glass. First we check whether the damp is merely condensation from the room; if the unit really has failed, it is measured, made to order and replaced in the sash you already have.

Our clients on video · all videos (in Bulgarian)

Misted insideThe seal has failed, so the unit is replaced as a whole
Made to sizeMeasured first, then ordered from a glass manufacturer
Sash staysThe unit changes, the profile does not
Drilling and dryingWe do not do it and do not recommend it
1000+ clients served 30+ years in the trade Price agreed before we start 06:00–23:00 every day
In short

Double glazing unit replacement in Varna is needed when there is moisture between the panes, when the glass is cracked or when its edge is chipped. Condensation on the room side is not a failed unit: that comes from humid air. When a unit has failed we measure, the unit is ordered to size from a glass manufacturer, and then it is replaced in the same sash, with the profile left alone. Because every unit is made to measure, it is not an off-the-shelf job and we give no lead time before the order is clear. The work is carried out by the craftsmen we work with; we organise it and remain your one phone number. Call +359 52 993 333 or email info@kanalvarna.com — write to us in English and we reply in English.

Updated November 2026

When a double glazing unit is replaced

A unit is replaced in three cases: moisture collects between the panes, the glass is cracked, or its edge is cracked or chipped. In all three the frame and the sash stay; only the unit changes.

Double glazing unit (glass unit). Two or three panes held apart by a spacer round the edge and sealed with a sealant. The spacer holds a drying agent, and the gap is filled with dry air or an inert gas. The unit is airtight, so moisture between the panes means the seal no longer holds.

The unit sits in the sash, or straight in the frame where a part does not open. It is held by glazing beads, the narrow strips along the inner edge, with rubber under them pressing against the glass. That is why on uPVC windows the job usually goes from inside without removing the window. The sealant at the edge ages with sun, cold and wind. A unit packed crookedly, or knocked by a heavy sash, tends to mist earlier. Other repairs are collected in the window and door repair hub.

Misted between the panes, or only damp on the room side?

It takes seconds to tell: wipe the pane on the room side with a dry cloth. If the damp disappears, it was on the surface, not in the unit.

An old window with several panes, condensation and dirt along their lower part
Condensation along the bottom of old panes: before a new unit is ordered, we check on which side the damp is
  • Room side. The damp wipes off and returns in the morning, mostly along the bottom edge. The unit is sound; the cause is humid air in the home, and a new unit does not cure it. See mould and damp.
  • Outside. The outer pane is wet on cool, humid mornings and dries later. That is normal: the unit keeps the warmth in the room, so the outer pane stays cold.
  • Between the panes. It cannot be wiped off from either side and there is fog, droplets or white marks on the inner surfaces. The seal is gone and the drying agent no longer takes up moisture. The unit has to be replaced.

Drilling and drying a misted unit is sometimes offered as a way to avoid a new one. The glass may look clear for a while, but the seal does not come back, any gas has already escaped and the coating inside can be damaged. We do not do such a repair and do not recommend it. If you are unsure where the damp is, send us a photo of the glass taken in the morning.

What you see, the likely cause and what is done

Double glazing units in Varna: sign, cause and remedy
What you noticeLikely causeWhat is done
Fog or droplets between the panes that do not wipe offThe unit has lost its sealMeasured, and replaced with a new unit made to size
Wet on the room side in the morning, along the bottom edgeHumid air in the home, a cold edge of the glassThe unit stays; we look for the cause of the damp
A web of cracks from one pointA knockTemporary covering, then replacement; toughened or laminated glass for a door or low pane
A straight crack from the edge with no knockOften uneven heating of the glass or a pinched edge from fittingReplacement, and a check of the packers and beads
Water between the glass and the beadA worn rubber under the bead or a blocked drain in the profileA new rubber during the replacement, or clearing the drain
The sash sagged after a unit was changedThe unit was packed wrongly or is heavier than the old oneRe-packing and adjusting the sash

If the cold comes not from the glass but along the frame or from the wall beside the window, the cause is usually the fitting joint or the seals, and a new unit will not help: see window seal replacement.

Tell us how many units there are, what the frame is made of and what happened; a photo of the marking helps. By phone we say whether and when we can come to measure.

📞 +359 52 993 333

Measuring and ordering: why it is not a job for tomorrow

A unit is not stock from a shelf; each one is made for a particular sash. So we measure first, the unit is then ordered from a glass manufacturer, and the lead time depends on the manufacturer and the type of glass. We tell you after we know the size and the make-up. At measuring we settle:

  • The size of the glass, not of the sash. The unit is smaller than the opening in the frame, to leave room for the packers. It is measured from the old unit or from the opening once the beads are off.
  • The thickness. It must suit the profile and the beads. A thicker unit needs narrower beads if the profile has them; otherwise it does not fit.
  • The type of glass. Doors and low glazing near the floor take toughened or laminated glass. Toughened glass breaks into small blunt pieces; laminated glass stays stuck to its film.
  • The coating. The low-emissivity coating is inside the unit and must be on the right pane. The exact position is in the make-up of the unit.
  • The marking. The spacer between the panes often carries the maker, the date and the make-up. A photo of it helps to order the same unit.
A hand holding a sample of an aluminium profile with a triple glazed unit in section
A profile sample with a triple unit in section: the thickness of the unit has to match the profile and the beads

Cracked glass until the new unit comes: tape over the crack on the room side with wide tape and do not open the sash. Do not lean out to tape the outside. If a piece is missing, cover the opening with plastic sheet or a board. Handle the glass only in thick gloves and keep children and pets away. If the outer pane on a high floor is cracked, do not try to remove the pieces yourself: glass falling outside is a hazard for people below. Call us and say how large the sash is.

Replacing the unit, step by step

  1. Beads off. Each glazing bead is levered off the profile with a thin spatula. Their places are marked, because they are cut to size for the sash.
  2. Old unit out. It comes out upright, with suction handles or gloves. A cracked pane is taped first so it does not fall apart. The old packers show how the sash was supported.
  3. Packers in the right places. The load-bearing packers go in by the diagram for the way the sash opens, usually on the diagonal from the bottom hinge corner to the top handle corner. That keeps the sash square and stops it sagging.
  4. New unit and beads. The unit is centred on the packers and the beads are tapped back with a rubber mallet until they click. A unit of different thickness takes beads for that thickness.
  5. Sash check. The sash is opened, tilted and closed. If it rubs, or the unit is heavier than the old one, the hinges are adjusted.

A fixed part is done the same way, with the unit straight in the frame. On old timber windows the question is whether the rebate in the sash is deep enough for a unit; on old aluminium a new unit improves the glass, but the cold frame stays cold. A new unit is not always sensible, and we say so: when the profile is cracked, the sash is bent, the timber is rotten or the whole window will soon be replaced anyway, the money goes into a frame that will not hold. We do not sell windows, so our advice is only about what makes sense.

What to tell us by phone, and what the price depends on

We give the price by phone after a short description, and the final one after measuring. It helps to know:

  • how many units there are and roughly how big;
  • uPVC, aluminium or timber, and whether the glass is in a sash, a fixed part or a door;
  • what happened: misted between the panes, cracked, a chipped edge;
  • a photo of the marking on the spacer, if it can be read;
  • which floor you are on, whether there is a lift, and whether the glass can be reached from inside.

The price depends on the size and make-up of the unit, the type of glass, the number of units, access and whether new beads or seals are needed. We do not take on work outside above the second storey; if a unit can only be changed from outside, we say so from your description. Somebody has to be there to let us in for both the measuring and the replacement: a neighbour, the building manager or whoever holds the keys. We work every day from 06:00 to 23:00.

Frequently asked questions

Can a misted double glazing unit be repaired?

Not lastingly. Moisture between the panes means the edge seal now lets air in. Drilling, drying and closing the holes can clear the glass for a time, but they do not bring back the seal or any gas. A new unit in the same sash is the proper remedy.

Can only one pane of the unit be replaced?

No. The unit is sealed as one piece, so for a cracked inner or outer pane the whole unit is ordered. Taken apart to change one pane, it would no longer be airtight and would mist soon. The new unit can have the same or a better make-up.

Can you replace a unit on a high floor?

On uPVC windows the beads are inside, so the job is done from the room and the floor rarely matters. More important are the size of the unit and the lift and stairs it has to pass through. We do not take on work outside above the second storey; if a unit can only be changed from outside, we tell you on the phone.

The glass mists on the room side. Will a new unit help?

Rarely. The warmer glass of a modern unit may reduce the droplets, but the moisture in the air stays and moves to the next cold place, such as the corner or the joint round the window. So we look for the cause of the damp first: see mould and damp.

I let my flat out and live abroad. Can you arrange it?

Yes. Email us the address and photos of the glass, the frame and the marking on the spacer, and tell us who will open the door for the measuring and for the replacement. Write to us in English and we reply in English; you get the price before the unit is ordered.

Misted between the panes, or cracked?

Tell us how many units there are, what the frame is made of and what happened; a photo of the marking helps. By phone we say whether and when we can come to measure.

📞 +359 52 993 333

or email info@kanalvarna.com — write in English and we reply in English.

Send us a message

Leave your name and a phone number with the country code. Add your email if you prefer a written reply — write in English and we reply in English. We confirm the price before any work starts.

📞