Ultrasonic leak detection in Varna: hearing a leak the human ear cannot
Water forced through a small crack makes a hiss far above the range of human hearing. An ultrasonic detector picks it up and turns it into sound in headphones, so we can follow it along a pipe or a wall to its source. Every day 06:00–23:00 in Varna and along the coast.
Our clients on video · all videos (in Bulgarian)
Ultrasonic leak detection finds a leak by the very high-pitched sound that water makes when it is forced through a small opening under pressure. The detector works between 20 and 100 kHz, above anything the human ear can hear, and gives us a sound in headphones and a signal level on a display; the closer we get to the leak, the stronger the signal. It is quick, is not put off by traffic or machinery, and suits pressurised pipes, valves and fittings within reach, including pipes in walls. We use it on its own or together with a thermal camera or an acoustic correlator, and we work every day 06:00–23:00 in Varna and along the coast. Call +359 52 993 333 or email info@kanalvarna.com — write to us in English and we reply in English. You pay after the job, in cash, by card or by bank transfer.
Updated November 2026How ultrasonic leak detection works
When water under pressure is pushed through a crack or a loose fitting, the flow becomes turbulent and gives off sound at a very high frequency. People hear up to about 20 kHz. Our detector works from 20 kHz to 100 kHz, so it picks up leaks that nobody could hear unaided.
- The sound is made. Water under pressure passes through a small opening and creates ultrasonic waves.
- The sensor picks it up. The receiver turns the waves into an electrical signal.
- The signal is cleaned up. The electronics amplify the signal and filter out background noise, so that only the sound of the leak is left.
- We listen and watch the display. The sound is shifted into the range of hearing and played through headphones, and the signal level is shown on the screen. The closer the sensor is to the leak, the stronger the signal.

When we use ultrasound
Ultrasound works best where there is pressure and a small opening. These are the cases where we reach for it first.
- Pressurised water pipes that are exposed or within reach — a small crack gives a clear signal.
- Valves and shut-off taps that may be passing water. The detector shows quickly whether a valve is sealing properly.
- Fittings and joints along a pipe run, where the leak is usually at the connection.
- Noisy places. Unlike acoustic methods, ultrasound is not affected by low-frequency noise such as traffic and machinery.
- Metal pipes in concrete. Sound travels well through the metal and the concrete.
- Rooms with an even temperature, where a thermal camera has little contrast to work with.
It is also quick: scanning a room takes about 10–15 minutes, and a full check of a flat 30–60 minutes of work, depending on how complicated it is. The sensor can pick up a leak from a short distance without touching the pipe, and it works on every pipe material — metal, PVC, PPR and copper.
Ultrasound, acoustic correlator or thermal camera?
These are not rivals. Each one is good at something, and a difficult leak is usually found by two of them together.
| Method | Good at | Weaker at |
|---|---|---|
| Ultrasound | Pressurised pipes, valves, fittings, noisy surroundings, quick scans of a room or a pipe run | Very small leaks with almost no flow, pipes without pressure, pipes buried deep in the ground |
| Acoustic detection | Long runs of pressurised pipe, buried and outdoor pipes, an exact position along the pipe | Plastic pipes, noisy places, pipes without pressure |
| Thermal camera | Hot-water pipes, heating, underfloor heating, the wet area behind tiles and plaster | Cold pipes deep in the ground, dry surfaces |
In practice, ultrasound confirms that there is a leak and gives us the area; the thermal camera then shows the wet patch on the surface, or the acoustic correlator gives the exact position along a buried pipe. Sometimes a pressure test confirms the leak first and ultrasound then locates it. To see how all the methods fit together, start from the main leak detection page; for long or buried pipes, acoustic leak detection explains the correlator in more detail.
Tell us where the water is and what the meter does — we tell you the price before we start and when we can come.
📞 +359 52 993 333How a visit goes
- Preparation. We check the pressure in the system and decide which area to scan.
- Scanning. We pass the ultrasonic sensor along the pipes, fittings, valves and walls.
- Locating. We find the point where the signal is strongest — that is where the leak is.
- Confirming. We double-check with a thermal camera or a moisture meter before anything is opened.
Heating pipes normally run at a lower pressure than the water supply, so for the check we may raise the pressure in the heating circuit with a hand pump. That makes the sound from the leak stronger and the result clearer. Afterwards you get a written record: where the leak is, which methods we used, the readings and our recommendation for the repair. If you need a written report for your insurer, ask when you book.
What ultrasound cannot do
Ultrasound is less effective on a very small leak with minimal flow, on pipes with no pressure — such as drains — and on pipes buried deep in the ground, where the soil muffles the signal. In those cases we add the acoustic correlator or a thermal camera. For a drain we use a camera instead: see CCTV drain survey. For a leak in the yard, start with the water meter test on our page about an underground water leak.
If you are not in Bulgaria
A flat that is empty for weeks, a guest who reports a damp smell, a high bill that arrives by email — many people who write to us in English find out about a leak from a distance. You do not need to travel. Send us the address and the name and phone number of the person who can open the door — the property manager, a neighbour, the cleaner or the guest — and we arrange the visit with them.
Photos help us prepare: the water meter with the taps closed, the damp patch, the pipe if you can see it. After the visit we let you know what we found and where, and you can pay by bank transfer. For flats that stand empty, a property check may be worth considering, and if damp has already set in, see mould and damp.
Price
Ultrasound does not have its own line on our price list; we use it as part of a leak detection visit, and the price depends on what needs checking. As a guide: acoustic leak detection is from €36, moisture meter readings from €30, thermal camera diagnostics €52 for the first flat and €26 for each further flat, and combined diagnostics with a written report from €55. Fixing the leak is from €40. We confirm the price before we start, once you have described the job. You pay after the work, in cash, by card (Visa, Mastercard) or by bank transfer, and we issue an invoice on request. See the price list.
Frequently asked questions
How does ultrasonic leak detection work?
A receiver picks up the very high-pitched sound that water makes when it is forced through a crack under pressure. We hear it through headphones and see the signal level on a display, and follow it to the point where it is strongest.
When is ultrasound better than a thermal camera?
For metal pipes in concrete, for valves and fittings, in rooms where the temperature is even, and where the pipe is under pressure. For underfloor heating and for the wet area behind tiles, a thermal camera is usually better. Often we use both.
How accurate is it?
In suitable conditions it can narrow a leak down to within about 10 cm. It is less precise on plastic pipes or deep underground, and then we add another method.
Does it work in a noisy flat or building?
Yes. The detector works at frequencies above household and street noise, and its filters remove the background sound.
How much does it cost?
Ultrasound is used as part of our leak detection, so there is no separate price for it. As a guide, acoustic detection starts from €36 and combined diagnostics with a written report from €55. We confirm the price before we start. See the price list.
I'm not in Bulgaria. Can you still deal with it?
Yes. Send us the address and the contact of whoever can let us in. We arrange the visit with them, let you know what we found, and you can pay by bank transfer.
Can I contact you in English?
Yes — write to us in English by email at info@kanalvarna.com or through the form on this page, and we reply in English. The phone number is +359 52 993 333.
Think there is a leak?
Tell us where the water is and what the meter does — we tell you the price before we start and when we can come.
📞 +359 52 993 333or email info@kanalvarna.com — write in English and we reply in English.
Send us a message
Leave your name and a phone number with the country code. Add your email if you prefer a written reply — write in English and we reply in English. We confirm the price before any work starts.