Kanal VarnaDrains • Leaks • Thermal imaging • Plumbing
Blue water meter between rusty stop taps and pipes on a wall

Water meter replacement in Varna: we fit it, ViK Varna seals it

The meter has stopped, drips from the union nut, or the tap in front of it will not shut off the water? The plumber we work with changes the meter and the stop tap. The seal and the registration are arranged with ViK Varna, the local water company.

Our clients on video · all videos (in Bulgarian)

We fit itNew meter and, if needed, a new stop tap
ViK Varna seals itWe do not break or place seals
Price firstTold before we start, after photos or a description
06:00–23:00Every day, weekends included
1000+ clients served 30+ years in the trade Price agreed before we start 06:00–23:00 every day
In short

For a water meter replacement in Varna, the plumber we work with shuts off the water, removes the old meter, cleans the strainer if there is one and fits the new meter with new gaskets, the arrow on the body pointing the way the water flows. If needed the stop tap is changed at the same time. The seal, the registration and the metrological check are done by ViK Varna, the local water company, or by the company that reads the meters in your building, so arrange the sealing with them before the work. We tell you the price before we start; it depends on the access, the tap and where the water can be shut off. See also the plumber in Varna page. Call +359 52 993 333 or email info@kanalvarna.com — write to us in English and we reply in English.

Updated November 2026

When a water meter needs replacing

A meter is replaced when it is broken, stuck, leaking or past its verification date. The reason is often visible: it drips around the body, the glass is cracked, or the numbers stand still while water is running. When you open a tap, the small wheel and the last digits on the dial should move.

Close-up of an old water meter dial with cubic metre counters
  • The meter has seized: water runs from the tap but the wheel and the digits do not move.
  • The body or glass is cracked, most often after a frosty night.
  • Water comes out of the meter itself and not from the nuts next to it.
  • The verification period has expired and ViK Varna or the metering company asks for a replacement.

If the meter is intact but there is simply no water in the cold, a frozen meter or pipe is more likely; see frozen pipes. If the small wheel turns while every tap is closed, the water is escaping somewhere after the meter: that needs leak detection, not a new meter.

Who does what: we fit it, ViK Varna seals it

The new meter is fitted by the plumber we work with. The sealing, registration and checking of the meter belong to ViK Varna, the local water company, or to the company that reads the meters in your building. We do not break or place seals.

WhoWhat
The plumber we work withRemoves the old meter, fits the new one, changes the stop tap if needed, checks the joints for leaks
ViK Varna or the metering companyPlaces the seal on the new meter and usually records its number and starting reading; they tell you which meters they accept
YouArrange the sealing, keep the photos and make sure the plumber can reach the meter and the riser tap

A seal that is broken without agreement can cause trouble with your readings even if the meter works perfectly. So the union nuts of a sealed meter are not undone until you have agreed with ViK Varna how the seal will be removed. Before the plumber comes:

  • Ask ViK Varna or the metering company what their procedure is and when they can come to seal the new meter.
  • Photograph the old meter so that the reading and the serial number can be read.
  • If you already have a new meter, check that it is for cold or hot water as needed and that its length and connections match the old one.
  • Keep the document that came with the new meter; the sealing may ask for it.

The tap in front of the meter does not close

If the stop tap in front of the meter does not shut, the water has to be turned off further upstream: at the riser tap, at the entrance of the building or, for a house, by ViK Varna, because the tap in the meter chamber usually belongs to them.

  • In a flat: the tap in front of the flat's meter is normally on the riser. If it is damaged, the whole riser or entrance is shut off and the neighbours lose water, so it goes through the building manager.
  • In a house: the tap in the chamber before the meter usually belongs to ViK Varna. If it will not close or it leaks, call them — they decide how the water is stopped.

An old tap that no longer holds is best replaced together with the meter: the water has to be shut off once anyway. If the riser itself is rusty and leaks in several places, look at riser pipe replacement.

If it is dripping while you wait:

  • Put a container under the drip and towels around it.
  • If the leak is after the meter and there is a tap there, close it.
  • Do not over-tighten the union nut or knock the tap: an old nut or body can crack and turn a drip into a jet.
  • If water reaches a socket, extension lead or appliance, switch off the circuit for that room, provided the fuse board is dry.

Symptom, likely cause and what we do

What you seeLikely causeWhat we do
Drips from the nut beside the meterOld or shifted gasket in the unionChange the gasket; if the nut is sealed, only after agreement with ViK Varna
Tap will not close fully, or the handle is brokenSeized or worn stop tapChange the tap; before the flat's meter, the riser is shut off through the building manager
Water runs but the wheel and digits stand stillSeized mechanism — limescale or damageReplace the meter after agreement with ViK Varna
Small wheel turns with all taps closedA leak after the meter: a cistern, a pipe in the wall or in the yardWe do not replace the meter; we look for the leak

A bill that has jumped for no clear reason is not a reason to buy a meter: check for a hidden leak first, then ask ViK Varna to check the accuracy. Hoses that keep bursting and a water heater valve that drips all the time can mean a pressure that is too high; that is a pressure reducing valve question.

Tell us where the meter is, whether it is for cold or hot water and whether the tap before it closes. We tell you the price before we start.

📞 +359 52 993 333

How the replacement goes

  1. Shut off and release the pressure. The tap before the meter is closed and the nearest tap in the flat is opened to drop the pressure. If the tap does not hold, the water is stopped at the riser or the entrance, and for a house by ViK Varna.
  2. Reading and number. Before the old meter is touched, its reading and number are photographed; the photo stays with you.
  3. Out with the old. The unions are undone, the meter comes off and the strainer in front of it, if any, is cleaned, so that sand and rust do not go into the new meter.
  4. New meter by the arrow. The new meter goes in with the arrow on the body pointing in the direction of the water, and the dial easy to read. The unions get new gaskets: the gasket makes the joint tight, not force.
  5. Leak check under pressure. The water is turned on slowly, air is let out through a tap, and every joint is watched for drips.
  6. Seal. The new meter stays unsealed until ViK Varna or the metering company arrives. We photograph the starting reading and number for them and for you.

A meter fitted backwards is a typical mistake of doing it yourself: it does not measure properly, and you only notice at the next reading.

Flat, house chamber or hot water

The work is the same, but the location decides how easy it is to shut off the water. In a flat the meter is usually in the bathroom, the toilet or a niche by the riser, often high up or behind a panel; if it is behind tiles with no opening, say so, because access has to be made first. In a house it is usually in a chamber in the garden or by the fence, and shallow chambers freeze first, so the meter and its pipes should be insulated afterwards. For the chamber itself, see water meter chamber.

A hot-water meter is made for a higher temperature and cannot be replaced with a cold-water one. Many flats in Varna have no separate hot-water meter, because the hot water comes from a water heater after the cold meter. Once you have described it, we tell you whether we can take on the hot-water meter in your building.

Water meter replacement: what the price depends on

There is no single price for a meter replacement. It depends on whether only the meter or the stop tap as well is changed, how hard the access is, the state of the pipes and threads, and where the water is shut off — at the tap before the meter, at the riser or at the entrance. We tell you the price before we start, after you have described the job or sent photos. Who buys the meter itself we agree with you; the sealing is done by ViK Varna or the metering company. If it turns out that the pipe after the meter is rotten, we tell you before we go on and agree the price again.

It helps to know:

  • where the meter is — in the flat, the basement or a chamber in the garden;
  • whether it is for cold or hot water;
  • whether the stop tap is to be changed as well and whether the tap before the meter closes;
  • a photo of the meter and the pipes around it.
Two hands tightening a brass fitting on a metal pipe

If you are not in Bulgaria

From abroad the practical difficulty is the sealing: that is arranged by you with ViK Varna, not by us. Email us a photo of the meter, its reading and number, the address and the name and phone number of the person who will open the door. We agree the price and the day with you. In a block, where the riser has to be shut off, the building manager must warn the neighbours. You pay after the work.

Frequently asked questions

Who seals the new meter?

ViK Varna, the local water company, or the company that reads the meters in your building, depending on who manages your meter. We fit the meter but we do not place or break seals. Arrange their visit in advance so the new meter is not left long without a seal and its starting reading is recorded.

Can I change the meter without telling ViK Varna?

We do not recommend it. If the old meter is sealed, taking it off without agreement means a broken seal, and that can cause trouble at the next reading. The new meter also has to be sealed and registered before it is used for readings. So call ViK Varna first, then us.

How long will I be without water?

If the tap before the meter closes, the water is off only for as long as it takes to change the meter and check for leaks. If the riser or the entrance has to be shut off, the neighbours are without water as well, so the time is agreed with the building manager. We tell you what to expect in your case.

I'm not in Bulgaria. Can you still deal with it?

Yes. Send photos and the address by email, name the person who will let us in and write to us in English — we reply in English. The sealing still has to be arranged with ViK Varna by the owner, and we tell you what to ask for. See also the plumber in Varna page.

Meter leaking or tap not closing?

Tell us where the meter is, whether it is for cold or hot water and whether the tap before it closes. We tell you the price before we start.

📞 +359 52 993 333

or email info@kanalvarna.com — write in English and we reply in English.

Send us a message

Leave your name and a phone number with the country code. Add your email if you prefer a written reply — write in English and we reply in English. We confirm the price before any work starts.

📞