Kanal VarnaDrains • Leaks • Thermal imaging • Plumbing
A sprinkler on a stand beside a tree, spraying a wide cloud of water over the grass

Irrigation system repair and winterising in Varna: start-up, valves, sprinklers, leaks

Water left in a valve or a sprinkler head turns to ice and cracks it. We drain the system before the frosts, start it up in spring and repair it in between: a zone that will not start, a head that will not pop up, a leak in the line.

Our clients on video · all videos (in Bulgarian)

Ice cracks partsWater left in a valve or a head expands when it freezes
Fill slowly in springA sudden rush of water hits the valves and the heads
Meter at both endsEvery visit starts and ends with the water meter
Systems built by othersWe service them too
1000+ clients served 30+ years in the trade Price agreed before we start 06:00–23:00 every day
In short

Irrigation system repair and servicing in Varna is usually up to three visits a year: start-up in spring, a check or repair during the season, and winterising in autumn. Winterising means draining the water out of the pipes, valves, filter and sprinklers before the first frost. We also repair a valve, a sprinkler, a controller or a leak in the line, and we take on systems we did not build. Every visit ends the same way: all zones stopped and the water meter checked. This is a newer line of work for us, so we tell you by phone whether and when we can come. It is part of garden irrigation in Varna. Call +359 52 993 333 or email info@kanalvarna.com — write to us in English and we reply in English.

Updated November 2026

What irrigation system servicing covers

A system that is looked after needs a visit in spring, one in the season if something goes wrong, and one in autumn. We take on systems that we did not build as well; for the full picture of what a system is, see garden irrigation in Varna.

  • Spring: start-up, a check of every zone, the nozzles and a new schedule.
  • During the season: a zone that will not start, a sprinkler that will not pop up, a wet patch or a higher water bill.
  • Autumn: winterising, before the nights turn frosty.

We end every visit the same way: all zones stopped, and a look at the water meter. That tells us whether the system holds its water before we leave.

Winterising an irrigation system before the cold

Winterise before the first night below zero; in Varna that is usually late autumn. The cold spells here are short, but one frosty night can crack a valve, a filter or a sprinkler, mostly the parts above ground and just under it. The first hoar frost on the grass is a sign that the system should already be empty.

Grass covered with hoar frost on a cold morning, close up
Hoar frost on the grass. By the time you see it, the water should be out of the pipes.
  • we shut the water to the system at its own tap;
  • we open the drain points at the lowest places and let the water run out;
  • we drain the filter and the backflow device, and take them off and put them away where that is needed;
  • we open the valves by hand so the water leaves them too;
  • we switch the controller off or to its rain mode, and tell you what not to touch until spring.

Blowing out. Some systems drain badly, and the water is then pushed out with a compressor. This is done only at low pressure suited to the parts, or the heads and joints are damaged; the air does not go through the backflow device, each zone is blown for a short time, and nobody stands by the heads, because water and sand come out under pressure. We do not own a compressor: where a system cannot be drained in any other way, the blowing out is done with a contractor's compressor, and we say so beforehand.

If the water meter chamber or the pipe to the house has already frozen, that is another job: see frozen pipes.

Spring start-up

In spring the water goes in slowly, so that it pushes the air out without a blow to the parts. A tap opened fully gives water hammer, which can crack a valve or throw a head out of its seat.

  1. We close the drain points and put the filter back.
  2. We open the system tap gradually until the main line is full; the air leaves through the heads.
  3. We run zone by zone: does each head rise, where does it throw, does it reach the next.
  4. We clean the nozzles and filter, replace heads the winter broke and look over the drip lines.
  5. We change the controller battery, check the rain sensor and set the schedule.

The spring schedule is shorter than the summer one and has to be changed again when the heat comes; the controller does not know it has got warmer.

Call and tell us how many zones the system has, where the valve box is and whether there is a drain point. We say whether and when we can come, and what to switch off until then.

📞 +359 52 993 333

A zone will not start, a sprinkler will not pop up: sign and cause

Most faults show in how the system behaves during a cycle.

Irrigation system repair: the sign, the likely cause and what we do
SignLikely causeWhat we do
One zone will not startA broken cable, a failed valve coil or a mistake in the programmeWe open the valve by hand to learn whether the valve, or the cable and controller, is at fault
A sprinkler will not pop upMud or grass around the head, low pressure, a broken springWe clean the head, read the pressure with the gauge and replace the sprinkler if needed
Water shoots up like a fountainA broken head or a snapped elbow under itWe dig around the head and replace what is broken
A puddle or a greener strip in one placeA leaking joint or a cracked pipe in the lineThe meter first, then zone by zone, last a small dig on the spot
The meter moves with the system offA valve that will not shut, or a leak before the valvesWe close the system tap: if the meter stops, the watering is losing water
The controller is dead or shows an errorNo power, a flat battery, a faulty sensorWe check the programme and the sensor; the 230 V supply is for an electrician

A leak in the irrigation line: how we find it

We look for a leak in order: first prove that the system is losing the water, then narrow it to a zone, and only then dig, so that there is one small hole.

  1. The meter. All zones off, the system tap open. If the meter moves and stops when this tap is closed, the loss is in the watering.
  2. Zone by zone. We run each zone and look for puddles, heads that rise weakly and water where there should be none.
  3. The pressure gauge. We fit it on the main line after the system tap, fill the line and close the tap. If the pressure drops with the valves closed, the leak is between the tap and the valves, or a valve lets water through.
  4. Listening. The acoustic device helps less on plastic irrigation pipe, where the noise dies out quickly, so we sometimes dig a trial hole where the search has narrowed to.
  5. The sketch. A plan or photos of the route from the build shorten the search a lot.

One distinction saves time. If the meter still moves with the irrigation tap closed, the leak is not in the system but before it, in the pipe to the house or in the house itself. That is a different search: see underground water leak and, for the method, acoustic leak detection.

How a visit goes, and what you can check first

You tell us what you see: which zone, since when, whether there is a puddle, what the controller says. If the system is not ours, we ask who built it and whether there is a sketch. On that call we also say whether and when we can come.

On site we read the meter with the system off, run each zone, and look at the heads, drip lines and valves in the box. We replace a head, nozzle, valve or piece of pipe on the spot if we have the part; if not, we order it and come again. We finish with the meter again and leave you a short written note of what was changed. If the system turns out to be badly made, say too many heads on one zone or no way to drain it, we say so and suggest a rebuild — see irrigation installation.

Some faults go away without a visit. Check these first:

  • the time and date on the controller — after a power cut some lose their settings;
  • the rain sensor — if it is wet, or stands where a sprinkler wets it, it stops the cycle;
  • the system tap — someone may have closed it;
  • the filter — a blocked filter lowers the pressure of all zones at once. Close the system tap, run a zone briefly to let the pressure fall, and only then unscrew and rinse the filter;
  • a manual start — if a zone runs by hand but not by programme, the schedule is at fault, not the pipes.

What to tell us, and what the price depends on

We give the price by phone after a short description. Tell us how many zones there are, what exactly does not work, whether there is a puddle and how the meter behaves with the system off, and email photos of the valve box and the controller to info@kanalvarna.com. If the house stands empty, tell us who holds the keys and opens the gate — a neighbour, a caretaker or whoever minds the house.

The price depends on the number of zones, on whether it is start-up, winterising or a repair, on the parts to be replaced, and on whether finding a leak needs a dig. It also matters whether the property is in Varna itself or in the villa areas around it. An outside tap or the main stop tap of the house that will not close is a job for a plumber, and a 230 V supply for the controller is an electrician's.

Frequently asked questions

When should I winterise the system in Varna?

Before the first night with a temperature below zero. In Varna that is usually late autumn, but every year differs, so watch the forecast rather than wait for the first hoar frost. If the house stands empty earlier, winterise when you leave. A week without watering is better than a cracked valve in spring.

What happens if I do not winterise?

Water left in the low stretches, in the valves and in the filter can freeze on the first frosty night and crack the weakest parts: the valve body, the filter, the joints under the heads. In spring it shows as a zone that will not stop, water bursting out of the box or a meter that moves with the system off. The repair is then usually bigger than the winterising.

Do you service a system you did not build?

Yes. We ask who built it, when, how many zones it has and whether there is a sketch of the route. If there is none, the first visit is longer: we find the valves, trace the zones and write down what we find, which makes the next time easier for both of us.

My water bill went up — is it the irrigation?

It may be. Compare the months with and without watering. If the jump is bigger than usual, stop all the zones and look at the meter; if it moves, close the system tap. If it stops, the watering is losing water. If it does not stop, the loss is elsewhere: see leak detection.

Do you come in summer if something stops working?

Repairs go on through the whole season. Tell us how serious it is: if a fountain is shooting up, close the system tap until we come; if one zone will not start, plants usually manage a few days with hand watering. Whether and when we can come, we say by phone.

Frosts coming and the system still full of water?

Call and tell us how many zones the system has, where the valve box is and whether there is a drain point. We say whether and when we can come, and what to switch off until then.

📞 +359 52 993 333

or email info@kanalvarna.com — write in English and we reply in English.

Send us a message

Leave your name and a phone number with the country code. Add your email if you prefer a written reply — write in English and we reply in English. We confirm the price before any work starts.

📞